I got the same issue, bought TP-LINK archer C4000 router few days ago, at first i was able to connect to the 2.4Ghz and set up everything. After a day, out of sudden 2.4ghz went missing, could find the SSID at all, following 5Ghz disappear too. After hard reset, only 5Ghz SSID can be seen. 2.4Ghz totally gone.
Connect your modem to the WAN port of the TP-Link router via an Ethernet cable;connect the main computer to TP-Link router's LAN port via an Ethernet cable. 3 ． Power on your router first, then the modem and computer. The main router will be connected to the TP-Link N router via LAN port (as seen below). The WAN port is not used for this configuration. Main Router Access Point. Step 1. Connect your computer to a second LAN port on your TP-Link N router using an Ethernet cable.* How to setup and login TP link Router. tp-link router login, tp link router setup, tp link setup. First get a broadband connection from any of the ISP (internet service provider) like Fiber Act, Airtel Broadband, BSNL etc Connection of ISP totally depends what options you have in your area. Usually this is all that is needed to connect your router to a wired connection. 3 Log In. Using a computer that is connected to the TP-Link router, open a web browser (such as Safari, Google Chrome or Internet Explorer). Using a computer that is connected to the TP-Link router, open a web browser (such as Safari, Google Chrome or Internet With an Ethernet cable, connect your PC to the second LAN port on the TP-Link N router. Use the IP address located on the bottom of the router to log into the TP-Link web interface. Click "Network," and then "LAN." Change the IP Address and enter the address found on your TP-Link N router. Reboot the router and use the new IP address to
Connect your modem to the WAN port of the TP-Link router via an Ethernet cable;connect the main computer to TP-Link router's LAN port via an Ethernet cable. 3 ． Power on your router first, then the modem and computer.
Wireless connection to the TP Link on my laptop worked fine then it showed "limited connection". Unplugged the TP Link WAN cable, re-plugged it and my wifi internet was back. 5 minutes later, "limited connection". Same thing with ethernet connection to TP Link. But the 1st router works perfectly. Reset, rebooted… no improvement. 1). Connect computer back to TP-Link router via a cable. Login the web interface of TP-Link router and then go to Advanced > Network > Internet and focus on the MAC Clone section. 2). Choose Use Current Computer MAC Address and click Save. Tips: when you do the MAC Clone, please use wired connection on your computer. Step 4. The following steps will vary by router manufacturer: Open a Web browser and access the router's user interface, according to the manufacturer's instructions. This is typically done by entering the router's IP address, like 192.168.1.254, into your browser's address bar. Within the router's User Interface, select Internet Connection type PPPoE. I got the same issue, bought TP-LINK archer C4000 router few days ago, at first i was able to connect to the 2.4Ghz and set up everything. After a day, out of sudden 2.4ghz went missing, could find the SSID at all, following 5Ghz disappear too. After hard reset, only 5Ghz SSID can be seen. 2.4Ghz totally gone.
In this tutorial, you will learn how to configure WDS (Wireless Distribution System) on TP-Link Wireless Routers. WDS helps you to connect two or more wireless access points together without wires.
Connect the other end of the Ethernet cable to the WAN port on your router. 5. Connect an AC adapter to your router and plug it in. 6. Connect a second Ethernet cable to a WAN port on your router. 7. Connect the other end of the Ethernet cable to a computer. 8. Open a web browser and enter the router's IP address in the address bar. The TP-Link Archer AX10 will upgrade your network with all of the new features that come with Wi-Fi 6, but it can't hit the same top speeds as fancier Wi-Fi 6 routers with more oomph to them. Then release the button and wait for the router to reboot to its factory default settings. Preparation. Power up the TP-link router. Connect an ethernet cable between port 1 of the RISE provided NTU and the blue INTERNET port of the TP-Link router. Connect a computer to any of the TP-Link's yellow ethernet ports using an ethernet cable. The easiest way to connect two routers is by using Ethernet. #connect2routers #tplink #netvn Thanks for watching, don't forget like and subscribe at https://goo.gl/LoatZE Caption author (Indonesian) In this tutorial, you will learn how to configure WDS (Wireless Distribution System) on TP-Link Wireless Routers. WDS helps you to connect two or more wireless access points together without wires.